Search Results for ‘magnum 425’

I have a 98 magnum 425 that has a lean condition. It over heats in minutes and idles extremely high I have cleaned the carb multiple times and it seems to get a little better for a bit but never great. I’m not sure what else to check

I know many people have had this problem before. I recently purchased a 98 Magnum 425. Guy said it would run but spit and sputter. I brought it home cleaned carb and some fresh fuel. Fired right up and idles perfect. Runs good up until about 1/5 throttle then starts spitting and sputtering and...

Received a free 1996 Polaris Magnum 4x4 from a relative who had no time to try to get it running. Going through the wiring and fixing/replacing bare wires when I noticed something. In front of the handle bars there is a switch mounted that looks like it was rigged. I traced the wiring from...

I am replacing the rockers and Cam on my 1995 Polaris 425 magnum, When i installed the new cam and put the rocker arm assembly in .. the rockers were very tight to move up and down to the point where i would have to tap them a little to get them to budge ... I've tried loosening the set screw...

Working on two bikes now. 1996 Magnum 425 and 2000 Xpedition 425. Both have the brake line from the master cylinder to the brake distribution block completely blocked with corrosion. At their age neither of these are high value bikes so I would like to repair at minimal cost. The Factory parts...

My 1998 Polaris magnum 425 recently lost spark. I was out riding when it bogged down and shut off. I let it cool down for a bit and then went to start it and the battery was dead. Tried pull starting it and the rope broke. Towed it home and let it sit for a couple days. Took the recoil apart...

Hey just picked up my first ever ATV. Old 1996 Polaris Magnum 425.. Definitely will Need some work but wanted to start with the basics, change fluids and oil. But I also wanted to give it a good cleaning before I started to work on it. Right now there is a ton of mud and sand caked on...

Good Morning! I recently inherited a 1995 Polaris Magnum 425 4x4 that is in fair condition. I have gotten it running and installed new brake pads. I bought a master cylindar rebuild kit and am beginning this adventure. My question is how do i get the piston out to replace the seals on the...

When I put the quad into four wheel drive only three out of the four tires will spin under power the front left is limp as its out of four wheel drive. What would cause this? Any info is appreciated. Thanks for all the help before I got the motor and alignment issues taken care of.

I need side plastics around the tank, both handle brake levers, a pull start ratchet, and bulbs for the front two lights

Thanks to cam101311 http://www.polarisatvforums.com/forums/members/2311-cam101311.html that gave me the idea of how to lift it. I took that idea and made a few changes. Check it step by step. Hope it helps you;: Now I am working on the rear shock ... it's bi**h to...

Hi I am new here so hello everyone, I have a couple question about a magnum 425 I am putting together for my dad. I have ordered a carb, master cylinder, shocks, petcock from a used dealer on the island. I received the parts and noticed the petcocl was different, it was the external one with 3...

Howdy.. i new to the forum and have tried searching for the answer but cant find it. i have a 96 425 magnum that grinds really bad when trying to put into gear, i am not sure if i need a new tranny, tranny work and if i do what other models will interchange with mine or do i have to get one from...

Hey guys, im new to the thread, and I have a 95 Polaris Magnum 425 4x4 and I think the carb is bad. when hooked up and i accelerate, the quad will barely rev above idle, but if i stick a screwdriver under the diaphragm slide and lift it up while reving, the motor roars like its supposed to. My...